BULKtalk: Choosing the right conveyor belt

30 Dec.,2024

 

BULKtalk: Choosing the right conveyor belt

Steve Davis, senior bulk handling expert at Advisian, explains the ins and outs of buying the right conveyor belt and how choosing the wrong one can cost millions.

If you want to learn more, please visit our website haichuan.

The conveyor belt is a significant component of the capital and operating cost of a conveyor. We should be looking for the best possible life from the belt and its splices, and taking every opportunity to minimise damage and wear, while meeting target throughput.

A conveyor belt that is volumetrically undersized for the duty will result in not meeting nameplate or produce spillage, both of which are ongoing losses to the operation, and costs in clean up and collateral damage. Many belts are designed around optimistic surcharge angles and reduced edge clearances or operated over original design parameters.

Poor loading onto conveyor belts leads to accelerated wear, carcass damage, belt tracking and reduced life.

At $200 per metre, a 20-kilometre conveyor (40-kilometre belting) is an investment of $8 million. For iron ore, the current value is currently about $80 per tonne and for a tonnes per hour conveyor, each hour lost is an opportunity cost of $400,000. The cost for an unplanned change-out of one reel of belt, assuming the belt is available, for two days, including labour and lost opportunity, would exceed $25 million.

What life to expect?

Conveyor belt life expectancy should be several years and perhaps more than 10 years before fatigue failure. Often in the mining industry, we see shorter lives. Three failure modes are common to all belts, cover wear, fatigue and overstress, and damage.

Cover wear is less of an issue when conveying low abrasive ores. Cover thickness, good load chute design with attention to loading speed and direction will result in good belt life.

Abrasive ores such as iron ore can cause one millimetre per month wear on short cycle conveyors. A three-year cover life for longer conveyors is good. Focus should be on load chute and skirt designs that minimise wear at the load point, and cover material and thickness that gives maximum practical life. The change in belt section from wear changes the tension distribution when wrapped around pulleys.

The selection of conveyor belting must be justified through comparative testing by TUNRA or similar, or some industry benchmarking to obtain the best cover material and longest life. Testing and experience indicate a wide range of wear rates between nominally similar compounds from respected suppliers, and for different ores. Particle size (coarse, lump, fine), moisture content, drop height, type of impact bed, belt speed and chute design all influence cover wear.

Related stories:

Fatigue failure is the result of many cycles of bending and stressing and occurs in covers and in the belt carcass. A conveyor that is well designed, installed and operated should see even fatigue across the width of the belt. Poor design of transitions and turn overs, curves, tripper and shuttle approaches are common causes of tension and fatigue bias across belt width. Build-up of ore on pullies and significant cover wear can result in localised high stresses in the belt that lead to early fatigue, typically on the edges or in the centre. Fatigue results in cover compound cracking, splice failure initiation, and carcass damage such as broken wires. Misalignments and over-tensioning can also bias tensions across the belt. If part of the width has failed, even in one location, the strength of the belt has been reduced, and progressive failure is probable. If not monitored, this can lead to unexpected belt failure.

Design of the conveyor should consider the minimum possible number of pulleys, minimum allowable diameters, correct pulley spacing to reduce reverse bending (the one second rule), and correct design of transitions and curves. Operations should consider the result of any action that changes the tensions and transitions.

Damage can result from many sources, and most can be anticipated.

' Ultraviolet (UV) cover damage seen as cracking and spalling. This can be reduced by covering belts and UV-resistant covers.

' Chemical and heat damage can be reduced by selecting the correct cover compound. Some dry fine materials such as cement and alumina, not normally considered chemicals, attack some cover compounds and cause cracking.

' Edge damage from tracking into structures and equipment can be reduced by installing belt drift monitors and aligning the conveyor.

' Damage from carry back and spillage build up on pulleys and idlers can be reduced by sizing the belt for the maximum throughput and installing quality belt cleaning and spill protection devices.

' Wind can turn the conveyor belt over or push it into structures resulting in spillage and damage. Wind barriers will prevent this.

' Damage to and from pulley lagging can be reduced by having correct lagging, minimising spillage, installing pulley cleaners, shedders and belt ploughs to keep spillage from entrapment between the pulley and belt.

' Damage from tramp metal is less easy to prevent but damage can be minimised by removal of tramp using an over belt magnet and by metal and rip detector systems at critical locations.

' Groove damage from a dragging belt skirt that removes cover rubber directly or by ore entrapment should be designed out.

' Idlers that fail into 'cookie cutters' and 'potato peelers' should not be used, and quality idler seals and bearing arrangements are preferred. Identify and change seized idlers before damage results.

' Limit belt damage by installing and maintaining quality cleaners and ploughs. Splice interface with cleaners and ploughs should minimise risk of 'digging in' under the front edge of the splice.

The above list is not exhaustive. Providing well designed and properly installed components with good access to maintain will not add much to the cost of a conveyor. The life of the belt will benefit, and most of the components will last longer. Plant safety will be better. A 20-kilometre belt will have approximately 75,000 idler rolls. Even if a cheaper roll is $20 less than a better-quality roll, does the potential $1.5 million saving balance out the $25 million potential loss from a small rip, not to mention the greater number of roll failures?

Belt strength selection

Computer design programs help select belts using user defined inputs like minimum bulk density, surcharge angle, edge clearance, design tonnage, belt speed and belt safety factor. They then define an acceptable belt strength based on the inputs and other components to suit. It is relatively easy to iterate the calculations and check options. Absolutes used in conveyor specifications should be viewed with care. For example, specifying a maximum speed of six metres per second may result in a wider or higher strength belt than 6.4 metres per second. There is no practical difference between these two speeds. Be flexible.

There are several load factors in use, nominal and design and other values for capacity are used. Interpretation varies, but it is vital the designer understands user expectations. Assuming a surcharge angle from a text often results in incorrect belt selection as, for various reasons, loading does not produce this angle. Low, zero, and even negative surcharges are common in practice, due to ore variation and chute configuration. Surcharge angle can reduce along long conveyors reducing edge clearance. Conveyor loading is rarely a steady state, as in belt design, and therefore an allowance for surging is appropriate. Feed from an apron feeder or bucket wheel can result in 25 per cent surging. Ore properties can be extremely variable. The best source of data is from a site visit to a similar conveyor.

Safety factors allow for inefficiencies in splicing, and account for many variables in the life of the belt, especially in the field where conditions are rarely ideal. The safety factor derates the nominal strength of the belt carcass to allow for these variables. Safety factors were first stated in DIN 22 101, , and there is considerable discussion around what to use in each application.

1. For fabric belts, belt safety factor is often a nominal 10:1. Little testing of fabric splices has been completed thus far. Many fabric belts have higher design safety factors if operating conditions are considered poor. If clip splices are used, consult the supplier.

2. Steel cord safety factors were a nominal 6.7:1, but advances in splice design and laboratory testing have led to consideration of lower factors, down to 4:1 or lower. There are several splice test facilities, so for a long or expensive belt it is worth testing the splice to confirm efficiency. Lower factors are acceptable and reduce belt strength requirement and cost, however splice quality in the field must be good quality, and other aspects of belt change during life should be considered.

3. Increasing the tonnage throughput on the conveyor reduces the safety factor when based on using 'spare' power and capacity. If it is likely this will occur, design initially with a margin or be prepared to change speeds and power.

4. Using smaller than recommended diameter pulleys or locating reverse bending pulleys too close, or any of the issues in the previous section, increase splice fatigue rate and further reduce the safety factor.

5. For longer life belts, the strength of carcass and splice will diminish with time.

6. Changing the belt source at a belt change-out could result in a different splice efficiency.

7. For conveyors with high dynamic belt tensions from stopping and starting, generally overland, the selection of take up type and other factors change belt tension requirements.

Each conveyor is different, as is each design team, so different solutions are possible. There is no single correct design or selection. I recommend clear user definition of expectations and minimum design inputs, and that the final design be re-evaluated when all details are firm. Due to differences in interpretation, I recommend an independent check of complex conveyor design at this stage.

The other parts of the belt

Having considered all the above, we now have belt speed, width and strength for the carcass of the belt. This is based on agreed design inputs.

There is no global standardisation on the make-up of the carcasses, so there may be several combinations of steel cord diameter and spacing that make up a particular strength. Fabric carcasses have more potential variations that achieve the same strength. Selection may be dictated by standardisation, otherwise allow suppliers some flexibility in proposals.

We have to select the compound for covers. There are many cover compounds available, and each manufacturer has their own proprietary mixes. Select covers that meet requirements. Options include low rolling resistance for bottom covers, gouge or abrasion resistant top covers, special covers for temperature or for alumina and cement, oil and chemical resistance colour and food grade. Grade M or N and other generics may be appropriate, but is it best for life costing? Are all similar grade covers the same? As noted earlier these compounds can be compared at a test facility.

Cover thickness is a trade-off of cost versus wear rate. Thicker covers may give a longer life but consider pulley diameters and belt cost. Most belt suppliers will provide guidance on selection of their belts. Most can meet the detailed manufacturing quality requirements of regional standards. Australian Standards require QC testing; do you need other tests?

Splices

Whether steel cord or fabric, all belts must be spliced to form an endless loop. The splice is the weak point in the belt and is the main reason we have a safety factor. Vulcanised splices rely on the spliced cover and filler compounds to carry belt tension in shear. There is no direct joining of the carcass materials. Splices require good design, and the quality of the equipment and process to make them in the field. Good conditions give best quality, so include splice facilities in the conveyor design.

Steel cord belts must be hot spliced. Fabric belts have the option of hot or cold splicing and 'clipping'. Hot splices must be between two pieces of belt with the same cord or carcass configuration and cover compounds. Cold splices for smaller belts may be able to join two similar pieces of belt. Belt clips are available in many different formats, and guidance from vendors is recommended. A detailed record of all splices should be maintained.

If site conditions are dirty, dusty or cramped, or if quality splices can't be guaranteed, increase the belt safety factor to compensate. Obtain a splice design from the belt supplier and ensure compliance.

All hot or cold splices require a splice kit. These contain glue and filler pieces, which are specific to the belt. Use of incorrect kits may reduce splice life. These kits have a shelf life and storage requirements, usually cool or cold. Once past expiry date they should not be used. Incorrect splice kit transport to site or cooler failure will affect splice quality. Some suppliers will confirm suitability of splice kits, which is beneficial for replacement of critical belt splices.

Splits, joints and edge sealing

Split belts, mostly fabric carcass, are available from many suppliers. Suppliers carry stock of a wide belt and slit it to width. This is useful in an emergency, but there are some risks in making sure the conveyor belt is compatible in a repair, and in some cases a resulting belt drift problem. Tracking is due to unbalanced tensions from splitting a symmetrical fabrication and generally cannot be fixed. Centre splits are better than edge splits as the tensions are likely to be more balanced. For fabric belts, clipping instead of splicing will avoid cover incompatibility. Split steel cord is rare, but I have seen different width belts with similar specification spliced for emergency repair.

Centre joints are when a wider than available belt is required, and results from two pieces of belt being longitudinally spliced together in the factory. The current maximum belt width is 3.2 metres, any wider requires a joined belt. I would not use these in a critical application.

Steel cord belts are generally made in the specified width with sealed edges. Fabric belts can be requested with or without sealed edges. Sealed edges protect the carcass from chemical or moisture ingress. Split belts always have one edge that is not sealed. Observation indicates that open edge fabric belts can start fraying after some time in service. Sealed edges do not protect against contact with structure but are better than unsealed.

Specifications

If the specification used to purchase belt and splice kits is not clear and detailed, there is a considerable risk of misinterpretation and incorrect supply. As belts are mostly made to specification, it can include valuable information such as the lead time for supply. Avoid being forced into using incompatible belts. A marked change in belt cover, cord or splice life after a repair can indicate that an incompatible belt was procured. Mechanical damage is generally independent of belt specification.

Are you interested in learning more about Steel cord belt for bulk material handling? Contact us today to secure an expert consultation!

Conveyor Belt Supplier: 7 Important Tips for Smart ...

Imagine a long, flat, moving sidewalk, like the ones you see at airports, but instead of carrying people, it is designed to move stuff from one place to another. That is what a belt conveyor is like. It is a big belt looped around two spinning wheels. One wheel makes the belt move, while the other just spins freely to keep the belt on track.

Conveyor belts are used in many places, such as factories, supermarkets, and even various restaurants! This strip is the conveyor belt, and it can move all sorts of items, helping to reduce excess time.

Having a Belt conveyor is not easy, as there are various factors involved. Let's check out the key factors in choosing belt conveyors from belt conveyor supplier to level up the business and save time.

What is a Conveyor Belt?

Conveyor belts are the workhorses of many industries, silently moving a wide variety of materials. They consist of a continuous loop of material, like rubber or fabric, stretched between pulleys. An electric motor rotates one or more pulleys, causing the belt to travel and carry whatever's on top for the ride.

These looped belts travel along a metal frame or rollers, and their applications are various. In factories, they move assembly line parts, while in warehouses, they transport goods. You will even find them at the grocery store, carrying your groceries to the checkout.
There are several types of conveyor belts designed for specific purposes. Flat belts handle everyday items, while inclined belts can move materials uphill. Special belts with cleats or grips can carry objects at an angle, and heavy-duty versions handle massive loads in mines and quarries.

Overall, conveyor belts are a simple yet ingenious way to automate transportation, saving labour costs and efficiently moving more goods and materials.

How Conveyor Belts Reduce Time Usage?

Conveyor belts revolutionize industries by streamlining material handling processes, significantly reducing time usage in several ways.

Automate the Repetitive Tasks

Firstly, they automate repetitive tasks, minimizing the need for manual labour. This automation ensures consistent and efficient movement of materials, eliminating the time spent on manual loading, unloading, and transportation.

Helps in Continuous Flow Production

Secondly, conveyor belts facilitate continuous flow production that makes seamless transitions between different stages of manufacturing or processing. This easier flow minimizes the idle time between tasks, maximizing productivity.

Makes the Work Faster and Efficiently

Moreover, belt conveyor supplier design for high-speed operation, allowing materials to be transported quickly from one point to another. This helps to boost the overall production cycle, reducing lead times and improving throughput.

Space Optimisation

Additionally, belt conveyor supplier manufacture with space utilization by transporting materials vertically, horizontally, or at inclines, efficiently utilizing available floor space in factories or warehouses.

Improved With Advanced Technologies

Furthermore, conveyor systems can be integrated with advanced technologies such as sensors, robotics, and automation software, further enhancing efficiency and reducing downtime through predictive maintenance and real-time monitoring.

Overall

In addition conveyor belts minimize time in material handling processes, promote workflow continuity, maximize space utilization, and utilize technology, collectively contributing to significant time savings in industrial operations.

7 Important Factors for Choosing a Belt Conveyor

Belt conveyors serve as a backbone of material handling in countless industries. They offer a reliable and efficient way to move a wide range of materials, from bulk powders to heavy equipment. However, with so many variations available, selecting the right conveyor from the right belt conveyor supplier for your specific needs can feel overwhelming. Here are seven important factors to consider when choosing a belt conveyor supplier

Material Handling Characteristics

Material Type
Understanding the material you'll be conveying is paramount. Factors like size, shape, weight, and abrasiveness all influence conveyor selection. Fine powders may require enclosed conveyors to minimize dust, while sharp objects need belts with high puncture resistance.

Capacity and Flow Rate
Determine the average and peak tonnage you need to convey per hour. This dictates the belt width, speed, and motor power required. Overloading a conveyor can lead to belt damage, spillage, and downtime.

Inclination Angle
Consider the maximum incline angle your chosen belt can handle if you need to upbring materials. This depends on the material's characteristics and the belt type (flat, cleated, etc.). Steeper inclines may require additional support structures or specialized belt types.

Conveyor System Design

Layout and Length
Plan the path your conveyor will take, considering space constraints, transfer points, and integration with existing equipment. The total length of the conveyor will influence factors like belt strength, number of support structures, and motor selection.

Discharge Method
How will the material be unloaded from the conveyor? Options include gravity discharge for free-flowing materials or scraper conveyors for sticky substances.

Feeding Method
How will the material be loaded onto the conveyor? Common methods include hoppers, vibratory feeders, or manual loading stations. The feeding method should ensure smooth and even distribution on the belt to prevent material build-up or spillage.

Belt Selection

Belt Material
Belts are made of various materials, such as rubber, PVC, or fabric. Consider factors like the material being conveyed, temperature extremes, and required strength. Rubber is versatile, PVC offers good chemical resistance, and fabric belts are ideal for lightweight applications.

Belt Width and Thickness
Choose a belt conveyor supplier width that comfortably accommodates your material flow and a thickness that offers sufficient strength for the weight it will carry. Wider belts handle larger volumes, while thicker belts are sturdier for heavy loads.

Cleats or Surface Texture
For inclined conveyors or those carrying slippery materials, consider belts with cleats or textured surfaces to prevent slipping and ensure proper material movement.

Support Structure

Frame Material
Conveyor frames are typically made from steel for strength and durability. In some cases, stainless steel may be needed for specific environments or food-grade applications.

Idlers and Rollers
These support the belt and ensure smooth travel. The type and spacing of idlers will depend on the belt type, weight capacity, and material being conveyed.

Take-Up System
Belts can stretch over time. A take-up system automatically maintains proper belt tension, preventing tracking issues and ensuring optimal performance.

Safety Features

Emergency Stops
Conveying systems should incorporate readily accessible emergency stop buttons to halt operations in case of accidents or malfunctions.

Guards and Covers
Moving belts and exposed components pose safety hazards. Guardrails, covers, and proper signage are crucial to prevent injuries and ensure safe operation.

Dust Control (if applicable)
Enclosed belt conveyor supplier may be necessary for dusty materials. Additionally, dust suppression systems like misters may be required to maintain air quality and worker safety.

Maintenance and Service

Accessibility
Design your conveyor system with easy access for routine maintenance tasks like belt inspection, cleaning, and replacement. Consider walkways, handrails, and strategically placed access points.

Spare Parts
Maintaining a readily available stock of critical spare parts, such as belts, idlers, and fasteners, minimizes downtime in case of unexpected breakdowns.

Manufacturer Support
Choose a belt conveyor supplier with a reputation for reliable after-sales service and readily available technical support. A responsive and knowledgeable service team is invaluable for maintaining optimal conveyor performance.

Budget and Cost Considerations

Initial Investment
Conveyor systems come in a range of price points depending on factors like length, capacity, and required features. Determine your budget upfront and choose a system that offers the necessary functionality without exceeding your financial limitations.

Long-Term Costs
Consider the lifespan of the conveyor, maintenance requirements, and energy consumption. While a lower initial cost may seem fine, a less efficient conveyor can lead to higher operating expenses in the long run.

Future Scope Of Belt Conveyor Supplier

Conveyor belts will become more integral to various industries in the near future, offering better innovation and practicality. The next-generation conveyors will prioritize safety, incorporating advanced sensors and AI algorithms to detect potential hazards and ensure smooth operations.

Moreover, belt conveyor supplier can be expected to play a vital role in sustainable manufacturing, with eco-friendly materials and energy-efficient designs that minimize environmental impact. They will also feature enhanced connectivity, enabling seamless integration with other smart technologies for real-time data exchange and predictive maintenance.

Ultimately, conveyor belts' future lies in their ability to combine efficiency, sustainability, safety, and human-centric design to revolutionize industrial processes.

Conclusion

Selecting the optimal belt conveyor for your needs goes beyond simply moving materials. It is an investment in efficiency, safety, and cost-effectiveness for your entire operation. By carefully considering the factors outlined above, from material characteristics and conveyor design to belt selection, support structure, and maintenance, you can ensure a smooth-running system that minimizes downtime and maximizes productivity.

Investing in a well-designed and properly maintained conveyor system yields numerous benefits. It reduces labor costs by automating material handling tasks, improves safety by eliminating manual lifting and carrying, and, most importantly, streamlines your workflow, ensuring a consistent flow of materials throughout your production or processing line.

Choose Bricspac for selecting the right belt conveyor supplier as we are India's best Conveyor Belt Suppliers. Our team researches the components and materials before manufacturing and assembling them. We also do quality checks for various cycles to make the machines work efficiently. This is why we are the leading belt conveyor supplier and export worldwide.

Frequently Asked Questions

What factors should I consider when choosing a conveyor belt?
Consider the type of material being transported, the environment (e.g., temperature, humidity), required speed, load capacity, and any specific industry regulations or standards.

How do I find out the appropriate width for my application?
Calculate the width based on the size and shape of the materials being transported, ensuring enough clearance on the sides to prevent spillage or jams.

What belt material is best suited for my needs?
Evaluate different materials such as rubber, PVC, polyester, or metal depending on abrasion resistance, flexibility, and suitability for specific environments (e.g., food-grade, chemical-resistant).

What type of conveyor belt design is most efficient for my operation?
Choose between options like flat belts, modular belts, or timing belts based on factors such as the complexity of the conveyor path, ease of maintenance, and adaptability to future changes.

How do I ensure safety features are integrated into my conveyor system?
Ensure the conveyor system includes safety features like emergency stop buttons, guards, and sensors to detect blockages or overloads. Consider training programs for personnel operating or working near the conveyor.

If you are looking for more details, kindly visit Steel cord conveyor belt for cement industry.